Call 08047674620 70% Response Rate

Send Email

Waterproofing Powder

Wholesaler of a wide range of products which include fosguard renderoc plug waterproofing powder.
FOSguard Renderoc Plug Waterproofing Powder
  • FOSguard Renderoc Plug Waterproofing Powder
  • FOSguard Renderoc Plug Waterproofing Powder
  • FOSguard Renderoc Plug Waterproofing Powder
  • FOSguard Renderoc Plug Waterproofing Powder

FOSguard Renderoc Plug Waterproofing Powder

Product Price: Rs 980 / 15KgGet Best Price

Minimum Order Quantity: 10 15Kg

Product Brochure

Product Details:
Usage/ApplicationConstruction
CategoryWaterproofing Coating
TypeBag
Purity100%
Shelf Life12 Months
Water Absorption8%
Form Of ChemicalSolid
FormPowder
Renderoc Plug is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a highly consistent, rapid setting mortar which is easy to apply in many difficult conditions. The material is based on a blend of cements, graded aggregates, special fillers and chemical additives which control the rate of set and minimise the risk of thermal cracking. Renderoc Plug provides an initial set time of approximately one minute.
Get Best QuoteRequest A Callback
FOSguard Renderoc Plug Waterproofing Powder
  • FOSguard Renderoc Plug Waterproofing Powder
  • FOSguard Renderoc Plug Waterproofing Powder
  • FOSguard Renderoc Plug Waterproofing Powder

FOSguard Renderoc Plug Waterproofing Powder

Product Price: Rs 100 / BagGet Best Price

Minimum Order Quantity: 10 Bag

Product Brochure

Product Details:
Usage/ApplicationConstruction
Packaging Size1 kg
CategoryWaterproofing Coating
Grade StandardReagent Grade
Purity95%
Shelf Life24 Month
Water Absorption8%
Packaging TypeBag
Form Of ChemicalPowder
BrandFOSguard
Uses

For the rapid temporary patching and plugging of concrete segments, concrete and brick tunnel linings, sewage systems, below ground access chambers, pipes, basements, foundations and mines.

Advantages

  • Emergency water-stopping capability
  • Single component - only the addition of clean water is required
  • Excellent bond to the substrate
  • Low exotherm minimises thermal cracking
  • Pre-bagged formulation to overcome variations in site batching
  • Contains no chloride admixtures

Description

Renderoc Plug is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a highly consistent, rapid setting mortar which is easy to apply in many difficult conditions. The material is based on a blend of cements, graded aggregates, special fillers and chemical additives which control the rate of set and minimise the risk of thermal cracking. Renderoc Plug provides an initial set time of approximately one minute. Design criteria Renderoc Plug can be applied to horizontal, vertical or overhead surfaces at a wide range of thicknesses. Generally, the volume of mixed material used in a single application is restricted to that which can be applied by trowel or gloved hand. Thicker sections can be built up in layers. If any doubt arises about the nature of the substrate, consult the local Fosroc office for further information.

Specification

Water stopping mortar The water stopping mortar shall be Renderoc Plug, a single component cement-based blend of powders to which only the site-addition of clean water shall be permitted. It must be chloride-free and must be formulated to prevent high exotherm and minimise thermal cracking.

Instructions for use
Preparation

Areas to be patched should be cut back to a depth of 15 mm and given a good mechanical key. Feather-edges must not be allowed. Surface should be brushed clean to remove loose material, dust and laitance. Grease, slime or mould growth should be removed by steam cleaning or high-pressure water jetting. A proprietary degreasing agent should be used for removal of light oil or grease contamination. To seal leaks, crack openings must be chased out to approximately 20 mm square. The chase should always be undercut to avoid leaving a v-section. All loose material and debris should be removed.

Mixing

Renderoc Plug should be added to clean water in the following proportions: one part clean water: 3 parts Renderoc Plug (measured by volume). Mix to a stiff consistency in a suitable mixing drum or bucket, using a trowel or gloved hand. Due to the rapid set characteristics of the product, only prepare a quantity of mortar which can be placed within the prescribed set time.

Application

Trowel apply or hand-knead the mixed mortar in place, ensuring maximum contact with the substrate before the material sets. If being used to plug running water, Renderoc Plug should be used and held in place until the initial set is reached.
Get Best QuoteRequest A Callback

EXPLORE MORE CATEGORIES

Contact Us
 
Thank youYour Enquiry has been sent successfully.
© H2O Bond Waterproofing Engineers. All Rights Reserved (Terms of Use)Developed and managed by IndiaMART InterMESH Ltd.